Grease injector – JINPINLUB

MGK-10 Quick Connector Volumetric Grease Distributor Device

JINPINLUB — Fri, 29 Nov 2024 09:59:40 +0000

Feature

1. Pressurized quantitative metering valve, a direct pressure action type.
The pressure oil delivered by the pump pushes the piston built into the metering valve to move, forcing the quantitative lubricant to be discharged.
When the pump stops working, the piston of the metering part is reset under the action of the spring force, that is, the quantitative lubricant is stored.
2. Accurate discharge, the metering part is discharged only once in one cycle, and the distance between each other in the system, whether it is far, near, high or low, horizontal or vertical installation, has no effect on the discharge.
3. Forced discharge, sensitive action. Two seals are used to prevent the discharged from flowing back.
4. Metering valves can be selected based on the needs of each lubrication point, and can be used in combination with the MGJ junction, either in series or parallel.
5. Sleeve type: Φ4 nylon tube needs to be combined with PA-4 joint and PB-4 double cone ferrule. Quick plug-in type: Φ4 nylon tube can be inserted.
6. Applicable to NLGI 000#, 00# grease.

Specification

Function principle	Pressure relief metering valve
Numbers of Outlets	1~12
Metering quantity	0.03, 0.05, 0.13, 0.20, 0.30, 0.50mL/cycle
Lubricant	NLGI 000#, 00# grease.
Operating temperature	-20 to +80 °C
Operating pressure	0.5~1.5MPa
Material	Copper, aluminum
Connection outlet	Inlet Rc1/8, Outlet Φ4(Rc1/8)
Outlet fittings	Sleeve type, Quick type
Mounting position	Any

Troubleshooting

Regular Inspection: Grease distributor wear, damage, and leakage should be checked, and all the connections must be tightened and aligned correctly.
Lubrication: The right type of grease applied to the distributor by the manufacturer’s instructions would lower friction and wear.
Cleaning: The grease distributor needs regular cleaning and its parts, as dirt, debris, or old grease might adversely affect the functioning of this part.
Replacement of Parts: Replace worn-out or damaged parts like seals or O-rings to avoid leakage and loss of efficiency.
Pressure Checks: Operating and reset pressures should be monitored for the specified range.

Manuals

View Datasheet - MGK Metering Valve

MGK Pressurized Grease Injector Metering Valves Series MG

JINPINLUB — Fri, 29 Nov 2024 07:26:22 +0000

Feature

Precise Lubrication Control: Distribution valves afford accuracy of discharge volume in a range of 0.03 mL to 0.5 mL for good lubrication.
Connection Methods: Distribution valves are offered with different connection methods: bushing, nut, one-touch connections, among others-that are easily adapted to the setup one is working on.
Durable Material: The valve bodies are of brass to make them strong and noncorrosive.
High Working Pressure: Distribution valves can bear working pressure from at least 1.2 MPa; thus, they are suitable for high-pressure applications.
Low Return Pressure: The return pressure is 0.5 MPa. This contributes toward the effectiveness of the system.
Compact Design: The dimensions are varied to fit various machinery and equipment.

Specification

Function principle	Pressure relief metering valve
Numbers of Outlets	1~12
Metering quantity	0.03, 0.05, 0.13, 0.20, 0.30, 0.50mL/cycle
Lubricant	NLGI 000#, 00# grease.
Operating temperature	-20 to +80 °C
Operating pressure	0.5~1.5MPa
Material	Copper, aluminum
Connection outlet	Inlet Rc1/8, Outlet Φ4(Rc1/8)
Outlet fittings	Sleeve type, Quick type
Mounting position	Any

Troubleshooting

Check for Blockages: Ensure that there are not any blockages within the metering valve or the piping. Clean any particles or buildup that is probably obstructing the glide.
Verify Connections: Make certain all connections are secure and there are not any leaks. Loose or faulty connections can affect the metering valve’s performance.
Inspect for Wear and Tear: Examine the metering valve for any symptoms of wear and tear, corrosion, or damage. Replace any tired components as needed.
Monitor Pressure Levels: Ensure that the running strain and return stress are within the particular variety. Incorrect strain tiers can cause troubles with lubrication.
Lubrication: Regularly lubricate the metering valve to make sure easy operation and prevent sticking.

Manuals

View Datasheet - MGK Metering Valve

MUK Precise Multi-Outlet Volumetric Grease Metering Device

JINPINLUB — Mon, 26 Aug 2024 20:05:54 +0000

Feature

Multi-outlet distribution: JINPINLUB MUK grease pressure relief distributors can be configured with 2 to 12 digits to meet the needs of different lubrication systems.
Umbrella valve design: The umbrella valve inside the distributor controls the flow of lubricant under the pressure of the lubrication system, making it very precise and distributed to various lubrication points.
Multiple outputs: The metering valve, one of the components of MUK, has multiple discharge volumes to choose from, such as 0.05, 0.1, 0.2, 0.3, 0.5mL/cycle.
Corrosion-resistant materials: MUK grease distributors are usually made of corrosion-resistant materials to adapt to different working environments.

Specification

Function principle	Pressure relief metering valve
Numbers of Outlets	1, 2, 3, 4, 5
Metering quantity	0.03, 0.05, 0.13, 0.20, 0.30, 0.50mL/cycle
Lubricant	NLGI 000#, 00# grease.
Operating temperature	0 to +80 °C
Operating pressure	0.5~1.5MPa
Material	Brass, aluminum
Connection outlet	Inlet Rc1/8, Outlet Φ4(Rc1/8)
Outlet fittings	Sleeve type, Quick type
Mounting position	Any

Principle

The lubricant flows out of the lubrication pump, and the system pressure pushes the piston in the MUK distributor upward. The lubricant stored in the oil chamber is discharged. When the piston moves to the top of the oil chamber, the oil discharge is completed.
When the lubrication pump stops supplying oil, the pressure relief valve will automatically release, allowing the lubricant in the main oil pipe to return through the pressure reducing valve. At this time, the system pressure is reduced, and the lubricant is stored inside the distributor, ready for the next cycle.

Manuals

View Datasheet - MUK Distributor

JL-1 Lubricant Positive Displacement Grease Dispensing Valve

JINPINLUB — Thu, 22 Aug 2024 05:12:02 +0000

Features

High-Pressure Operation: The JL-1 grease dispenser is capable of operating at high pressures ranging from 127 to 240 bar, ensuring that lubricant is effectively delivered to each lubrication point.
Adjustable Output: The output of each dispenser is externally adjustable from 0.016 to 1.31 cm³, which allows the user to precisely control the amount of lubricant dispensed based on specific needs.
Visual Inspection: The indicator needle design lets in the user to confirm the working status of the grease dispenser by visual inspection to make sure that the device is operating properly.
Easy Maintenance: The individual dispensing valves can be easily removed for inspection and replacement, reducing maintenance time and costs.

Specification

Function principle	Pressure relief metering valve
Numbers of Outlets	1, 2, 3, 4, 5, 6
Metering quantity	0.016-1.31mL/cycle
Lubricant	Grease NLGI 0, 1, 2
Operating temperature	(-26 to +176 °C)
Operating pressure	127-240 bar
Material	Carbon steel, stainless steel
Connection main line	M22*1.5
Connection outlet	Rc 1/8
Mounting position	Any

Application

The JL-1 grease distributor is mainly used in multi-point, high-pressure, unmarried-line pressure remedy grease lubrication systems, so the distributor is widely utilized in industries that require green lubrication control.
Mining and mineral processing: In these environments, gadget requires continuous lubrication to make certain green operation and decrease put on.
Construction equipment: Construction equipment often works under harsh conditions, and the JL-1 distributor can provide reliable lubrication.
Steel and heavy industry: Equipment in those industries often requires high-pressure lubrication structures to hold operation.

Manuals

View Datasheet - JL-1 Grease Injector

Jl-1 Grease Injector For Pressure Relief Single Line System

JINPINLUB — Thu, 22 Aug 2024 05:05:45 +0000

Features

Specification

Function principle	Pressure relief metering valve
Numbers of Outlets	1, 2, 3, 4, 5, 6
Metering quantity	0.016-1.31mL/cycle
Lubricant	Grease NLGI 0, 1, 2
Operating temperature	(-26 to +176 °C)
Operating pressure	127-240 bar
Material	Carbon steel, stainless steel
Connection main line	M22*1.5
Connection outlet	Rc 1/8
Mounting position	Any

Application

Manuals

View Datasheet - JL-1 Grease Injector

JL-1 High Pressure Metering Device For Single Line Lube System

JINPINLUB — Wed, 17 Jul 2024 13:08:15 +0000

Features

1. High-pressure operation: The JL-1 metering device is suitable for high-pressure environments; its working pressure range is 127-240 bar while the release pressure is rated at 41 bar.
2. Externally adjustable output: The output from the device is externally adjustable in the range of 0.016-1.31 cm³ to be used in various lubrication needs .
3. Indicator needle design: Every metering device is equipped with an indicator needle that permits visual inspection of its operating condition and therefore guarantees lubrication reliability.
4. Material selection: The JL-1 metering device has two material options: carbon steel and stainless steel for use in different environments. The stainless steel version is applicable for working environments that are hostile to carbon steel.
5. Multi-port design: The device can carry 1 through 6 lubrication points; thus, it is flexible in its ability to adapt to various lubrication system requirements.
6. Easy maintenance: Individual metering equipment is easy to dismantle for inspection purposes or replacement of worn-out parts, thus saving time for maintenance and reducing the overall maintenance costs.

Specification

Function principle	Pressure relief metering valve
Numbers of Outlets	1, 2, 3, 4, 5, 6
Metering quantity	0.016-1.31mL/cycle
Lubricant	Grease NLGI 0, 1, 2
Operating temperature	(-10 to +80 °C)
Operating pressure	127-240 bar
Material	Carbon steel, stainless steel
Connection main line	Rc3/8
Connection outlet	M22*1.5
Mounting position	Any

Application

1. Mining and mineral processing: Metering devices JL-1 are widely applied in mining and mineral processing industries, providing systems with reliable lubrication during very hard work.
2. Construction machinery: In the field of construction equipment, JL-1 metering device guarantees that each equipment lubrication point is well lubricated to extend equipment life.
3. Iron and steel industry and heavy industry: This equipment is also applied in a wide scope in the steels and heavy industries, stably working under high pressure and high temperature environments.

Manuals

View Datasheet - JL-1 Grease Injector