Pressure relief metering valve – JINPINLUB

MGK-10 Quick Connector Volumetric Grease Distributor Device

JINPINLUB — Fri, 29 Nov 2024 09:59:40 +0000

Feature

1. Pressurized quantitative metering valve, a direct pressure action type.
The pressure oil delivered by the pump pushes the piston built into the metering valve to move, forcing the quantitative lubricant to be discharged.
When the pump stops working, the piston of the metering part is reset under the action of the spring force, that is, the quantitative lubricant is stored.
2. Accurate discharge, the metering part is discharged only once in one cycle, and the distance between each other in the system, whether it is far, near, high or low, horizontal or vertical installation, has no effect on the discharge.
3. Forced discharge, sensitive action. Two seals are used to prevent the discharged from flowing back.
4. Metering valves can be selected based on the needs of each lubrication point, and can be used in combination with the MGJ junction, either in series or parallel.
5. Sleeve type: Φ4 nylon tube needs to be combined with PA-4 joint and PB-4 double cone ferrule. Quick plug-in type: Φ4 nylon tube can be inserted.
6. Applicable to NLGI 000#, 00# grease.

Specification

Function principle	Pressure relief metering valve
Numbers of Outlets	1~12
Metering quantity	0.03, 0.05, 0.13, 0.20, 0.30, 0.50mL/cycle
Lubricant	NLGI 000#, 00# grease.
Operating temperature	-20 to +80 °C
Operating pressure	0.5~1.5MPa
Material	Copper, aluminum
Connection outlet	Inlet Rc1/8, Outlet Φ4(Rc1/8)
Outlet fittings	Sleeve type, Quick type
Mounting position	Any

Troubleshooting

Regular Inspection: Grease distributor wear, damage, and leakage should be checked, and all the connections must be tightened and aligned correctly.
Lubrication: The right type of grease applied to the distributor by the manufacturer’s instructions would lower friction and wear.
Cleaning: The grease distributor needs regular cleaning and its parts, as dirt, debris, or old grease might adversely affect the functioning of this part.
Replacement of Parts: Replace worn-out or damaged parts like seals or O-rings to avoid leakage and loss of efficiency.
Pressure Checks: Operating and reset pressures should be monitored for the specified range.

Manuals

View Datasheet - MGK Metering Valve

MGK Pressurized Grease Injector Metering Valves Series MG

JINPINLUB — Fri, 29 Nov 2024 07:26:22 +0000

Feature

Precise Lubrication Control: Distribution valves afford accuracy of discharge volume in a range of 0.03 mL to 0.5 mL for good lubrication.
Connection Methods: Distribution valves are offered with different connection methods: bushing, nut, one-touch connections, among others-that are easily adapted to the setup one is working on.
Durable Material: The valve bodies are of brass to make them strong and noncorrosive.
High Working Pressure: Distribution valves can bear working pressure from at least 1.2 MPa; thus, they are suitable for high-pressure applications.
Low Return Pressure: The return pressure is 0.5 MPa. This contributes toward the effectiveness of the system.
Compact Design: The dimensions are varied to fit various machinery and equipment.

Specification

Function principle	Pressure relief metering valve
Numbers of Outlets	1~12
Metering quantity	0.03, 0.05, 0.13, 0.20, 0.30, 0.50mL/cycle
Lubricant	NLGI 000#, 00# grease.
Operating temperature	-20 to +80 °C
Operating pressure	0.5~1.5MPa
Material	Copper, aluminum
Connection outlet	Inlet Rc1/8, Outlet Φ4(Rc1/8)
Outlet fittings	Sleeve type, Quick type
Mounting position	Any

Troubleshooting

Check for Blockages: Ensure that there are not any blockages within the metering valve or the piping. Clean any particles or buildup that is probably obstructing the glide.
Verify Connections: Make certain all connections are secure and there are not any leaks. Loose or faulty connections can affect the metering valve’s performance.
Inspect for Wear and Tear: Examine the metering valve for any symptoms of wear and tear, corrosion, or damage. Replace any tired components as needed.
Monitor Pressure Levels: Ensure that the running strain and return stress are within the particular variety. Incorrect strain tiers can cause troubles with lubrication.
Lubrication: Regularly lubricate the metering valve to make sure easy operation and prevent sticking.

Manuals

View Datasheet - MGK Metering Valve

MG2K-8 PDI Metering Injector For Single Line Grease System

JINPINLUB — Thu, 28 Nov 2024 16:49:30 +0000

Feature

Combination: The distributor consists of a metering valve and a junction. You can select the appropriate output and assemble it into an MG2K distributor as needed.
Metering Valve: The MG2 valve meters grease correctly, maintaining a constant and economical feed.
Grease Nipples: MG2K is able to grease 1-12 plural points with one operation of a grease pump.
Material: The body is normally of brass to make it strong and resistant to corrosion.
Operating Pressure: Operating pressure range of 2.5 MPa with a reset pressure of 1.4 MPa.
Discharge Volume: Available in several discharge volumes, like 0.03, 0.05, 0.1, 0.2, 0.3, and 0.5 ml/cycle.

Specification

Function principle	Pressure relief metering valve
Numbers of Outlets	1~12
Metering quantity	0.03, 0.05, 0.13, 0.20, 0.30, 0.50mL/cycle
Lubricant	NLGI 000#, 00#, 0#, 1# and 2#
Operating temperature	-20 to +80 °C
Operating pressure	≥2.5MPa
Material	Aluminum+Copper
Connection outlet	Inlet M10x1/Rc1/8, Outlet Φ4(M8x1)
Outlet fittings	Sleeve type, Quick type
Mounting position	Any

Installation

Preparation:
Gather tools and materials, including a valve, grease nipples, fittings, and the appropriate type of grease.
Positioning:
Point out where the metering valve is to be installed. It should be an easy-to-reach area for maintenance and operation purposes.
Fittings Connection:
Couple the fittings to the metering valve and the grease lines. Be sure all are properly fit together to avoid leakages.
System Testing:
Install the valve and nipples and then test the system by working the grease gun. Check the system for leaks or improper grease flow.
Final Adjustments:
Check that all components operate properly and that the lubrication system supplies grease as intended.

Manuals

View Datasheet - MG2K Distributor

MG2K Grease System Pressure Relief Quantitative Distributor

JINPINLUB — Thu, 28 Nov 2024 13:44:02 +0000

Feature

1. Pressurized quantitative metering valve, a direct pressure action type.
The pressure oil delivered by the pump pushes the piston built into the metering valve to move, forcing the quantitative lubricant to be discharged.
When the pump stops working, the piston of the metering part is reset under the action of the spring force, that is, the quantitative lubricant is stored.
2. Accurate discharge, the metering part is discharged only once in one cycle, and the distance between each other in the system, whether it is far, near, high or low, horizontal or vertical installation, has no effect on the discharge.
3. Forced discharge, sensitive action. Two seals are used to prevent the discharged from flowing back.
4. MG2K metering valves can be selected based on the needs of each lubrication point, and can be used in combination with the MG2J junction, either in series or parallel.
5. Sleeve type: Φ4 nylon tube needs to be combined with PA4 compression bushing and PB4 sleeve. Quick plug-in type: Φ4 nylon tube can be inserted.
6. Applicable to NLGI 000#, 00#, 0#, 1# and 2# grease.

Specification

Function principle	Pressure relief metering valve
Numbers of Outlets	1~12
Metering quantity	0.03, 0.05, 0.13, 0.20, 0.30, 0.50mL/cycle
Lubricant	NLGI 000#, 00#, 0#, 1# and 2#
Operating temperature	-20 to +80 °C
Operating pressure	≥2.5MPa
Material	Aluminum+Copper
Connection outlet	Inlet M10x1/Rc1/8, Outlet Φ4(M8x1)
Outlet fittings	Sleeve type, Quick type
Mounting position	Any

Application

MG2K is used in machine tool industries for the lubrication of CNC machine tools, lathe machines, milling, grinders, and more to ensure long life of efficiency at work.
Automated production line: MG2K in the automated production line to ensure the lubrication needs of continuous operation and improve production efficiency.
Engineering machinery: such as excavators, loaders and other heavy machinery equipment, reduce equipment wear and extend service life.
Textile machinery: the MG2K is used to lubricate textile equipment, allowing it to run without hindrances.

Manuals

View Datasheet - MG2K Distributor

MUK Pressure Relief Metering Device For Precise Lubrication

JINPINLUB — Mon, 26 Aug 2024 20:13:22 +0000

Feature

JINPINLUB MUK is a pressure-type quantitative metering unit. It discharges accurately. In one working cycle, the metering component only discharges once. In the lubrication system, the metering component can be installed far, near, high, low, horizontally or vertically without affecting its operation. It discharges forcefully and moves sensitively. The metering valve is designed with two sealing connections to prevent discharge backflow.

Specification

Function principle	Pressure relief metering valve
Numbers of Outlets	1, 2, 3, 4, 5
Metering quantity	0.03, 0.05, 0.13, 0.20, 0.30, 0.50mL/cycle
Lubricant	NLGI 000#, 00# grease.
Operating temperature	0 to +80 °C
Operating pressure	0.5~1.5MPa
Material	Brass, aluminum
Connection outlet	Inlet Rc1/8, Outlet Φ4(Rc1/8)
Outlet fittings	Sleeve type, Quick type
Mounting position	Any

Application

MUK grease single-line metering device is widely used in the machine tool industry, including lathes, milling machines, grinders and other mechanical equipment. It can not only effectively reduce the wear of mechanical parts, but also reduce the failure rate of equipment and extend the service life of equipment. In addition, it is also suitable for other industrial equipment that requires precise lubrication, such as printing presses, textile machinery and food processing equipment.

Manuals

View Datasheet - MUK Distributor

MGK Pressurized Grease Distributors For Single-Line System

JINPINLUB — Mon, 26 Aug 2024 19:45:23 +0000

Feature

Precise metering: JINPINLUB MGK distributors provide precise lubrication quantity for each lubrication cycle, ensuring the best condition of the equipment.
Versatility: MGK injectors are suitable for a variety of lubricants with a viscosity range of NLGI 000#, 00#, 00#.
High reliability: The manifold is made of aluminum alloy and the metering valve is made of brass, which ensures the overall long-term reliability and durability of the grease distributor.
Easy operation: The metering valve of the MGK distributor is removable, and MG metering valves with different output volumes can be selected according to different lubrication requirements.
Strong adaptability: The wide operating temperature range (0°C to 80°C) can adapt to different working environments.

Specification

Function principle	Pressure relief metering valve
Numbers of Outlets	1, 2, 3, 4, 5
Metering quantity	0.03, 0.05, 0.13, 0.20, 0.30, 0.50mL/cycle
Lubricant	NLGI 000#, 00# grease.
Operating temperature	0 to +80 °C
Operating pressure	0.5~1.5MPa
Material	Copper, aluminum alloy
Connection outlet	Inlet Rc1/8, Outlet Φ4(Rc1/8)
Outlet fittings	Sleeve type, Quick type
Mounting position	Any

Application

MGK grease distributors are widely used in various industrial equipment that require precise lubrication. The metering valves on the distributor can be freely assembled and disassembled, which is convenient for customization or maintenance and replacement.
Grease metering valve mainly is used in medium and large-sized lubrication systems but also can be applied to mechanical equipment with high precision in lubrication, such as machine tools, woodworking machinery, textile machinery, packaging machinery, plastic machinery, glass machinery, and printing machinery. These lubrication valves ensure that the equipment works normally with precise lubrication during the operation of the system and prolong its service life.

Manuals

View Datasheet - MGK Metering Valve

MGK Pressure Relief Distributor For Single-Line Grease System

JINPINLUB — Wed, 17 Jul 2024 08:36:45 +0000

Features

Specification

Function principle	Pressure relief metering valve
Numbers of Outlets	1, 2, 3, 4, 5
Metering quantity	0.03, 0.05, 0.13, 0.20, 0.30, 0.50mL/cycle
Lubricant	NLGI 000#, 00# grease.
Operating temperature	0 to +80 °C
Operating pressure	0.5~1.5MPa
Material	Copper, aluminum alloy
Connection outlet	Inlet Rc1/8, Outlet Φ4(Rc1/8)
Outlet fittings	Sleeve type, Quick type
Mounting position	Any

Application

Single-line pressure relief grease lubrication system special distributors are widely used in mechanical equipment that requires precise lubrication, such as construction machinery, mining machinery, automobile manufacturing, etc. They are particularly suitable for those occasions where there are many lubrication points and it is necessary to ensure that each point can be properly lubricated.

Manuals

View Datasheet - MGK Metering Valve